com5SnowSlide: Snow slide

The com5SnowSlide computational module provides the option to add an elastic cohesion force between particles based on com1DFA. This can be used for example to simulate small snow slides.

The cohesion between particles is modeled using elastic bonds with maximum strain rate. This means that the cohesion force \(\mathbf{F}_{lk}\) exerted by \(l\) on \(k\) is expressed by:

\[\mathbf{F}_{lk} = -\mathbf{F}_{kl} = \frac{L-L_0}{L_0} A_{kl} E \mathbf{e_{kl}}\]

Where \(L\) and \(L_0\) are the distances between the particles \(k\) and \(l\) at a time t and at rest (initial time step), \(E\) is the elastic modulus of the material, \(A_{kl}\) is the contact area between particles \(k\) and \(l\) and \(\mathbf{e_{kl}}\) is the unit vector

\[\epsilon = \frac{L-L_0}{L_0}\]

represents the strain (\(\epsilon\) is positive in the case of elongation and negative in compression). If the strain exceeds a critical value \(\epsilon_c\) the bond between the particles \(k\) and \(l\) breaks.

The contact area \(A_{kl}\) between particles \(k\) and \(l\) reads:

\[A_{kl} = h_{kl} d_{kl} = \frac{h_k + h_l}{2} \frac{L}{\sqrt{3}}\]

\(h_{kl}\) represents the height of the contact surface and \(d_{kl}\) represents the length of the contact surface in the horizontal plane assuming that each particle has 6 neighbours.

Input

The standard inputs required to perform a simulation run using com1DFA can be found here: Input. There is a run script to perform a snow slide com1DFA run: runCom5SnowSlide.py, and the configuration settings can be found in com5SnowSlide/com5SnowSlideCfg.ini. The snow slide-specific parameters are:

snowSlide is activated by setting snowSlide to 1

the maximum strain before breaking of the bond cohesionMaxStrain

the Young modulus in N/m² cohesiveSurfaceTension

However, also several other parameters, for example the particle initialization method, friction model and parameters, are changed compared to the default configuration of com1DFA and listed in the com5SnowSlide/com5SnowSlideCfg.ini in the com1DFA_override section.

Please note that the provided default setup for snow slide calculation is defined with the following premises:

slope gradient in the release area from approx. 28° to approx. 50°.

a return level for hazard mapping of 150-yr of snow depth as the initial value.

movement as an intact unit without turbulence

height difference from approx. 30 m to max. 60-80 m

valid for altitude levels > 500 m and < 1,500 m sea level

Initialization of bonds

If the elastic cohesion (snowSlide set to 1) is activated, the bonds between particles are initialized. The construction of the bonds is done by building a triangular mesh on the particles (used as a point cloud) and the Delaunay triangulation function from matplotlib. The length \(L_0\) of the bonds at rest (initial distance between two bonded particles) is also initialized here.

Note

It is recommended to use the triangular (triangular) initialization option (Initialize particles) rather than the random or the uniform one in the case where cohesion is activated.

To run

first go to AvaFrame/avaframe
copy avaframeCfg.ini to local_avaframeCfg.ini and set your desired avalanche directory name
create an avalanche directory with required input files - for this task you can use Initialize Project
copy com5SnowSlide/com5SnowSlideCfg.ini to com5SnowSlide/local_com5SnowSlideCfg.ini and if desired change configuration settings
if you are on a develop installation, make sure you have an updated compilation, see installation:Setup AvaFrame
run:
```
python3 runCom5SnowSlide.py
```